Outboard decal Replicas - Find them here!

Evinrude/Johnson 1989 1990 3HP J3BRCEC J3BRESR ENGINE COVER

Evinrude/Johnson 1990 3HP J3BRESR ENGINE COVER

1) 0283680 STARTER HOUSING ASSY., Ev. - Evinrude 3BR
6) 0283719 ENGINE COVER, Lower, Ev.

0283725 DECAL SET, Ev. - Evinrude BR models Only

1) 0432755 STARTER HOUSING ASSY., Jo. - Johnson 3BR
6) 0392943 ENGINE COVER, Lower, Jo.

0433037 DECAL SET, Jo.- Johnson BR Models Only

0283680, 0432755, 0283719, 0392943,
0283680 0432755 0283719 0392943

PAINT CHART

E.S. NO.

COLOR

SPRAY CAN

*OMC/PPG COLOR CODE

1655

PRIMER

172757

ZINC CHROMATE

1678

WHITE

173744

81WJ1

1756

SILVER

282342

87SE1

1779

BLUE

211132

89BE1

*PPG REFINISHING COLOR CODE NUMBERS ARE LISTED FOR YOUR CONVENIENCE (FORMERLY DITZLER). PLEASE USE THESE COLOR CODE NUMBERS AT YOUR LOCAL PPG DISTRIBUTION CENTER WHEN LARGER QUANTITIES ARE DESIRED.

 
1989 Evinrude Outboard 3HP E3BRCEC  ENGINE COVER
1990 Evinrude Outboard 3HP E3BRESR ENGINE COVER
1989 Johnson Outboard 3HP J3BRCEC ENGINE COVER
1990 Johnson Outboard 3HP J3BRESR ENGINE COVER

Evinrude/Johnson EVINRUDE 1987 35/40/50 HP 

Evinrude/Johnson EVINRUDE 1987 40 HP E40TLCUD

 

ENGINE COVER - EVINRUDE Diagram

1) 0283034 ENGINE COVER ASSY., 50 Ev.
1) 0283033 ENGINE COVER ASSY., 50 Ev.
1) 0283032 ENGINE COVER ASSY., 40 Ev.
1) 0283031 ENGINE COVER ASSY., 40 Ev.
1) 0283232 ENGINE COVER ASSY., Evinrude 35 models

0283034, 0283033, 0283032, 0283031, 0283232
0283034 0283033 0283032 0283031 0283232

 

Evinrude Decals

11) 0210459 PLATE, Applique, front 50 model
14) 0210629 PLATE, Applique, rear 50 model

0210459, 0210629, 028333,
0210459 0210629 028333

11) 0210497 PLATE, Applique, front 40 model
14) 0210625 PLATE, Applique, rear 40 model

0210497, 0210625, 028333,
0210497 0210625 028333

11) 0210887 PLATE, Applique, front 35 model
14) 0210891 PLATE, Applique, rear 35 model 

0210887, 0210891, 028333,
0210887 0210891 028333,

26) 0283338 DECAL SET

 

More Articles …

  1. JOHNSON 2001 60/70 40JET
  2. EVINRUDE 1998 150 E150FCXECR
  3. Evinrude/Johnson EVINRUDE 1995 25SI/25SIK 50/60/70 E70TLEOR 1995
  4. 1983 EVINRUDE 35 HP

Subcategories

  • Mercury-Mariner-Tracker-Force Outboard Decals

    DECAL DRY APPLICATION

    IMPORTANT: This document guides our dealers, boatbuilders, and company service personnel in the proper installation or service of our products. If you have not been trained in the recommended servicing or installation procedures for these or similar Mercury Marine products, have the work performed by an authorized Mercury Marine dealer technician. Improper installation or servicing of the Mercury product could result in damage to the product or personal injury to those installing or operating the product.
    NOTE:After completing installation, place these instructions with the product for the owner's future use.
    IMPORTANT: This decal set must be applied dry. Do not use a soap and water mixture to apply this decal set.

    Tools, Materials, and Surface Requirements

    Tools and Materials

    • Decal application squeegee (3M® Applicator PA 1 Gold - recommended)
    • Air release tool (3M Air Release Tool 391x) or a straight pin - used to remove trapped air bubbles
    • Clean microfiber towel (Meguiar’s® Supreme Shine Microfiber Towel - recommended)
    • Spray bottles and labels for each cleaning solution
    • Cleaning solution:
      a. Liquid dishwashing soap
      b. Isopropyl alcohol
      IMPORTANT: Identify each spray bottle of cleaning solution with a label.

    Surface Requirements

    Special attention is required when applying decals to certain surfaces, including primed, painted, and certain plastics. All
    painted surfaces must be cured per the manufacturer's requirements. When applying decals to plastic surfaces, allow proper
    time for out gassing.

    Surface Preparation

    Application Temperature

    Apply the decal when the surface and ambient air temperature is between 16-373 °C (61-99 °F).
    NOTE: Applying the decal near the minimum temperature specification, the adhesive bond will develop more slowly than temperature in the mid to upper specification range.

    Step One General Cleaning

    IMPORTANT: Do not shortcut the cleaning process. All of the surfaces are considered contaminated prior to a thorough
    surface cleaning preparation.

    1. Mix a solution of 29.5 cc (1 fl oz) liquid dishwashing detergent with 3.7 Liter (4 US qt) of warm water.
    2. Rinse cowl with clean water.
    3. Dry the cowl with a clean Meguiar‘s Supreme Shine Microfiber Towel.
    4. Avoid detergents or preparations that contain waxes, oils, or lotions.

    Step Two Solvent Cleaning

    1. Mix a solution of isoprooyl alcohol and water to a 1:1 ratio. Store in a spray bottle and identify the solution with a label.
    2. Saturate a clean paper towel with the isopropyl alcohol and water solution.
    3. Wipe the cowl with the saturated towel followed immediately with a lint-free towel before the solution evaporates.
    NOTE: Isopropyl a/coho/ evaporates quickly. You must Wipe the surface immediately after applying the solution.
    4. When the paper towel becomes contaminated with dirt, discard it and use a clean paper towel saturated with the
    isopropyl alcohol and water solution.
    5. Ensure the surface has no contamination and is completely dry.
    6. Start to apply the decals immediately after solvent cleaning.

    Decal Application

    Application Tips

    1. Ensure that the surrounding work area and the surface are properly cleaned to avoid contamination.

    90-8M0143239 eng MARCH 2018       © 2018 Mercury Marine      -     Page 1 / 16

  • Evinrude-Johnson Outboard Decals
  • Nissan-Tohatsu Outboard Decals
  • Yamaha Outboard Decals
  • Suzuki Outboard Decals
  • Honda Outboards